WELD REALITY - TIP TIG WELDING PICTURES

HASTELLOY. REQUIREMENT, FAST WELD TRAVEL RATES, NO SPATTER, MINIMUM DISTORTION. WELDS WITH CONSISTENT WELD FUSION. PULSED MIG COULD NOT DELIVER. TIP TIG DID.

WELD REALITY - TIP TIG WELDING PICTURES

HOW CAN YOU COMPARE THESE TWO? TIP TIG 100% SOUND WELD. TIP TIG 5 x FASTER. TIP TIG NO SMOKE OR SPATTER. TIP TIG LESS SKILLS. TIP TIG HIGHER ENERGY CONCENTRATED ARC.

WELD REALITY - TIP TIG WELDING PICTURES

HOW CAN YOU COMPARE FLUX CORED OR STICK TO THIS TIP TIP WELD? LOOK AT THE WELD ENERGY, FLAT SURFACE, WELD CONTINUITY, THE WELD EDGES, NO START STOPS, NO SPATTER.

WELD REALITY - TIP TIG WELDING PICTURES

MANUAL TIP TIG CLAD: FIRST TIME INCONEL 625 TRIAL WELD. TYPICAL 0.045 WIRE FEED SETTINGS 120-160 INCH/MIN (5 TO 7 TIMES MORE WIRE THAN MANUAL TIG) WELD SET 250-270 AMPS. NO MANUAL TIG WELDER COULD DUPLICATE THIS WELD. BETTER WELD QUALITY THAN PULSED MIG.

WELD REALITY - TIP TIG WELDING PICTURES

STAINLESS, INCONEL, DUPLEX, THE METAL DOES NOT MATTER. WHAT MATTERS WITH TIP TIG,
YOU CAN USE TWO HANDS AND YOU ARE PRODUCING SUPERIOR QUALITY WELDS.

WELD REALITY - TIP TIG WELDING PICTURES

DUPLEX TIP TIG. IN CONTRAST TO PULSED MIG OR FLUX CORED NOTE THE TIP TIG WELD ENERGY
(DUPLEX IS SLUGGISH) AND NOTE THE WELD CLEANLINESS.

WELD REALITY - TIP TIG WELDING PICTURES

ALLOY 400. NOTE THE EXCEPTIONALY CLEAN, HIGH ENERGY FLUID WELD. ZERO WELD DEFECTS. INSTEAD OF THE TYPICAL 25-30 IPM FROM THE TIG WELDER TIP TIG DELIVERED 300 IPM

WELD REALITY - TIP TIG WELDING PICTURES

WHEN YOU CAN PUT MIG WELD DEPOSITION RATES WITH TIP TIG AND PROVIDE SUPERIOR WELD QUALITY, NO WELD FUMES, NO WELD SPATTER AND A SMALL HAZ, WHY BOTHER WITH MIG?

WELD REALITY - TIP TIG WELDING PICTURES

TIP TIG AUTOMATED WELDS ON 15 MM DUPLEX. WELD SPEED 15 INCH/MIN AND
OF COURSE DEFECT FREE WELDS.

WELD REALITY - TIP TIG WELDING PICTURES

TIP TIG WIRE FEED UNITS CAN BE USED WITH MOST TIG EQUIPMENT. AS TIP TIG TYPICALLY
USES HIGHER CURRENT, ON MANY APPLICATIONS 300 TO 400 AMP UNITS ARE IDEAL.

WELD REALITY - TIP TIG WELDING PICTURES

TIP TIG. ULTIMATE CONTROL OF THE WELD WIRE IS JUST AS IMPORTANT ON SMALL CODE QUALITY WELDS. THIS WALL THICKNESS IS 6 MM NOTE THE SMALL HAZ OF THIS MULTI-PASS WELD

WELD REALITY - TIP TIG WELDING PICTURES, MANUAL WELDS

TIP TIG "MANUAL WELDS". NOTE AGAIN THE WELD CONTINUITY. IN REALITY THESE WELDS LOOK
LIKE THEY ARE MECHANIZED ORBITAL WELDS. NOTE ALSO THE SMALL HAZ.

WELD REALITY - TIP TIG WELDING PICTURES, VERTICAL

TIP TIG P91. COULD YOU PRODUCE A MANUAL VERT UP WELD LIKE THIS. NOTE THE LACK
OF START STOPS. WITH TIP TIG WELD CONTINUITY IS ALWAYS IMPRESSIVE.

WELD REALITY - TIP TIG WELDING PICTURES , MANUAL TIG

MANUAL TIP TIG. A SINGLE WELD PROCESS FOR P91 WELDS. TWO SIMPLE WELD PROCEDURES AND WELD QUALITY AND MECHANICAL PROPERIES NEVER BEFORE ATTAINED

WELD REALITY - TIP TIG WELDING PICTURES, STAINLESS VESSEL

STAINLESS VESSEL TIP TIG WELDED FROM THE OUTSIDE / INSIDE AT THE SAME TIME
NO BACK GOUGING. TWO HANDS ON THE TORCH & WELDS MADE 200% FASTER THAN TIG.

WELD REALITY - TIP TIG WELDING PICTURES

STAINLESS OR ANY ALLOY VESSEL. CHEMICAL PLANTS, REFINERIES OR POWER PLANTS NO OTHER PROCESS WILL PROVIDE THE MANUAL WELD QUALITY ATTAINED FROM TIP TIG.

WELD REALITY - TIP TIG WELDING PICTURES, AUTOMATED

INCONEL, ALUMINUM, STAINLESS, THE ALLOY DOES NOT MATTER. WITH THE TIP TIG SEMIAUTOMATIC PROCESS, ROTATE THE PART AND YOU HAVE AN AUTOMATED PROCESS

WELD REALITY - TIP TIG WELDING PICTURES, TORCH POSITION

TIP TIG P91. ITS NICE IN THE OVER HEAD POSITION TO REST YOUR HAND ON THE
PIPE AND IMPROVE YOUR BALANCE, OR USE TWO HANDS ON THE TORCH

WELD REALITY - TIP TIG WELDING PICTURES, AUTOMATED TIG

EXAMINE THE APPLICATION RANGE OF TIP TIG
WELDING 1 mm DUPLEX HIGH SPEED AUTOMATED WELD

WELD REALITY - TIP TIG WELDING STAINLESS STEEL PICTURES

TIP TIG WELDING SMALL STAINLESS TUBES. CAN YOU IMAGINE HOW MUCH MORE WELD
CONTROL THIS TIP TIG WELDER HAS WITH BOTH HANDS HOLDING THE TORCH?